Explanation:
Here some of the pairs of terms are given. We need to find the incorrect relation. The relation are as follows :
1. amplitude of a sound: intensity of the sound
2. frequency of sound waves: number of wavelengths
3. quality of a sound: frequency of the sound
4. frequency of sound waves: loudness of the sound
The intensity of sound is directly proportional to the square of its amplitude. So, relation 1 is correct.
If f is the frequency and [tex]\lambda[/tex] is the wavelength. Speed of sound wave is,
[tex]v=f\lambda[/tex]
So, relation 2 is correct.
The quality of sound wave depends on its amplitude. So, relation 3 is not correct.
The vibration depends on two factors i.e amplitude and the frequency. The loudness of sound depends on the amplitude of wave. So, relation 4 is incorrect.
The incorrectly related pair in the given set is "quality of a sound: frequency of the sound" because it is the unique combination of frequencies and intensities, and not only the frequency, that determines the quality (timbre) of a sound.
Explanation:In the provided set of term pairs, the pairing "quality of a sound: frequency of the sound" is incorrectly related. While the frequency of a sound wave indeed influences the pitch of a sound, it doesn't determine the quality (or timbre) of the sound directly. The timbre of a sound is determined by the unique set of frequencies and intensities produced by a musical instrument or a voice, not by the frequency of the sound alone.
On the other hand, aspects like the "amplitude of a sound: intensity of the sound" and "frequency of sound waves: number of wavelengths" are correctly related. Larger-amplitude waves indicate greater pressure maxima and minima, thus higher intensity sounds. Similarly, the frequency is related to the number of wavelengths that pass in a given amount of time.
The pair "frequency of sound waves: loudness of the sound" can be both correct and incorrect depending on interpretation. Loudness is perceived volume and is influenced by both intensity and frequency. At the same frequency, greater intensity equates to more loudness. However, if the frequency changes without adjusting intensity, it can affect our perceived volume due to the varying sensitivity of human ears at different frequencies. Thus, frequency alone does not specify 'loudness'
Learn more about Sound Wave Properties here:https://brainly.com/question/31811556
#SPJ5
What would happen to Earth if ocean floor were created at divergent boundaries at a faster rate than it is destroyed at convergent boundaries?
Answer:
The Earth would increase in volume
Explanation:
What would happen to Earth if ocean floor were created at divergent boundaries at a faster rate than it is destroyed at convergent boundaries?
Divergent boundaries are boundaries where plates pull away from each other, forming mild earthquakes and volcanoes as magma comes to the surface. Earthquakes are as a result of vibrations travelling within the earth or ocean floors . Volcanoes occur as a result of the eruption of molten magma from the ocean floor
In divergent boundaries, the plates pull away and and the weakened crust in between collapse leaving more space thereby increasing in volume.
Convergent boundaries are boundaries that pull into each other. mountain chains are formed as the two plates push into each other if they are of the same density.
if you were to look for a cut on the palmar surface of a dog's leg where would you look?
Answer:
If you were to look for a cut on the palmar surface of a dog's leg then you should look at the back area of the front leg below the carpus.
Explanation:
Final answer:
To find a cut on the palmar surface of a dog's leg, you would check the underside of the foreleg where the paw pads are located.
Explanation:
If you want to locate a cut on the palmar surface of a dog's leg, you would look at the underside of the dog's foreleg. In humans, the palmar surface refers to the palm of the hand, and similarly, in quadrupeds like dogs, it refers to the analogous area - the bottom of their paws on the forelegs, where dogs have pads that contact the ground. This is analogous to the palm of the human hand although covered with different skin and touch pads.
Water can pile up a short distance above a container's rim due to: a. high capillary action. b. low viscosity. c. low surface tension. d. high surface tension. e. high viscosity.
Answer: a. high capillary action.
Explanation:
Water can pile up a short distance above a container's rim due to high capillary action. Capillarity is process by which water falls or rise through a narrow capillary tube. The concept allows water to rise to a certain height through the container before dropping.
A sound system is being set up in a gazebo in a park. It needs to produce music so that everyone can hear it. How much power would the speakers need to produce in order for the intensity at 5 meters away to be 1 x 10^-8 W/m^2? (assume the shape of the propagation of the sound wave is a hemisphere)
1.87 x 10^-7 W
1.57 x 10^-6 W
1.14 x 10^-6 W
2.46 x 10^-7 W
Answer:
Power, P=1.57×[tex]10^{-6}[/tex] Watt
Explanation:
Given
Intensity, I=1×[tex]10^{-8}[/tex] W/m²
Distance, r=5 meter
Considering the hemispherical space with radius 5 meter centered on the speaker. Speaker emits sound wave continuously with Power P. Intensity I is constant throughout the space and defined as power per unit area.
I=[tex]\frac{P}{A}[/tex]
so, P=I×A
where A is the area of shape of propagation.
since ,shape of propagation is hemispherical
so, A=2×p×r²=2×3.14×5×5=157 m²
P=1×[tex]10^{-8}[/tex]×157
P=1.57×[tex]10^{-6}[/tex] Watt
In which one of the following circumstances could mechanical energy not possibly be conserved, even if friction and air resistance are absent?
A car moves down a hill, its velocity continually increasing alongthe way.
A car moves up a hill at a constant velocity.
A car moves along level ground at a constant velocity.
A car moves up a hill, its velocity continually decreasing alongthe way.
Answer:
A car moves up a hill at a constant velocity
Explanation:
Since the velocity is constant, the speed is also constant and so is the kinetic energy. However, total mechanical energy is sum of gravitational potential energy and kinetic energy, and the car is moving up the hill so its potential energy rises.
Thus, in the circumstances described the mechanical energy cannot be conserved.
The correct answer is A car moving up the hill with constant velocity.
A metal ball at 30°C is dropped from a height of 6.2 km. The ball is heated due to the air resistance and it completely melts just before reaching the ground. The molten substance falls slowly on the ground. If the specific heat of lead = 126 Jkg−1^o C^{-1} and melting point of lead = 130^oC and suppose that any mechanical energy lost is used to heat the ball, then the latent heat of fusion of lead is:__________.
Answer:
Explanation:
Given
height [tex]h=6.2 km[/tex]
Initial temperature [tex]T_1=30^{\circ}C[/tex]
Specific heat of lead [tex]c=126 J/kg-^{\circ}C[/tex]
Melting Point of Lead [tex]T_m=130^{\circ}C[/tex]
Here Potential Energy is converted to heat energy to melt the lead ball
Sphere ball will first will be heated to [tex]130^{\circ}C[/tex] then it starts melting
thus
[tex]mgh=mc\Delta T+mL[/tex]
where [tex]L=latent\ heat\ of\ fusion[/tex]
[tex]\Delta T=[/tex]change in Temperature
[tex]gh=c\Delta T+L[/tex]
[tex]9.8\times 6.2\times 1000=126\times (130-30)+L[/tex]
[tex]L=48,160\ J/kg [/tex]
[tex]L=48.16\ kJ/kg[/tex]
Antoinette was diagnosed with hypertension, a noncommunicable disease in which her blood pressure is higher than normal. What is the most likely explanation for why she is hypertensive? She was obese and had a diet high in salt intake. She did not wash her hands enough. She was bitten by a mosquito. She was never vaccinated against hypertension.
Answer:
She was obese and had a diet high in salt intake.
Explanation:
higher blood pressure is condition known as hypertension which is the main cause of many heart problems which can be life threatening. In obese people. high level of fats inside the blood vessels which can cause blockage inside and can lead to heart problems.
high concentration of salts intake also disturbs the salts concentration in the blood vessels. The disturbance in salt concentration is the function of the kidney to remove it. the increase concentration also cause increase in blood pressure which leads to hypertension.
Answer:
She had a diet high in salt intake.
Explanation:
Sodium is medically known to raise blood pressure.
Washing hands and mosquitos are not related to blood pressure.
There is no vaccination against high blood pressure.
Suppose a 52 N sled runs on packed snow. The coefficient of friction is only 0.11. If a person weighing 700 N sits on the sled, what force is needed to pull the sled across the snow at constant speed?
Answer:
A force of 83 N is needed to pull the sled with constant speed.
Explanation:
Hi there!
Please, see the attached figure for a graphical description of the problem.
We have the following horizontal forces applied on the sled:
F = applied force.
Fr = friction force.
And the following vertical forces:
N = normal force.
W = weight of the sled + weight of the person
According to the Newton´s second law:
∑F = m · a
Where "m" is the mass of the object and "a" is its acceleration
So, in the horizontal direction:
F - Fr = m · a
We have to find what force, F, is needed so that the sled moves with constant speed (acceleration = 0). Then:
F - Fr = 0
F = Fr
The applied force has to be equal in magnitude to the friction force.
The friction force is calculated as follows:
Fr = μ · N
Where μ is the coefficient of friction and N is the normal force.
To find the normal force, let´s apply Newton´s second law in the vertical direction:
∑F = N - W = m · a
Notice that the sled is not accelerated in the vertical direction so that a = 0:
N - W = 0
N = W
The normal force is equal to the weight and the weight is the sum of the weight of the sled plus the weight of the person:
W = 52 N + 700 N = 752 N
Then:
N = 752 N
Fr = 0.11 · 752 N
Fr = 83 N
Then
F = 83 N
A force of 83 N is needed to pull the sled with constant speed.
A force of 83 N is needed to pull the sled with constant speed.
We have the following horizontal forces applied on the sled:
F = applied force.
Fr = friction force.
And the following vertical forces:
N = normal force.
W = weight of the sled + weight of the person
According to the Newton´s second law:
F = m * a
Where "m" is the mass of the object and "a" is its acceleration
So, in the horizontal direction:
F - Fr = m *a
To find what force, F, is needed so that the sled moves with constant speed (acceleration = 0). Then,
F - Fr = 0
F = Fr
The applied force has to be equal in magnitude to the friction force.
The friction force is calculated as follows:
Fr = μ · N
Where μ is the coefficient of friction and N is the normal force.
To find the normal force, let´s apply Newton´s second law in the vertical direction:
F = N - W = m · a
Notice that the sled is not accelerated in the vertical direction so that a = 0:
N - W = 0
N = W
The normal force is equal to the weight and the weight is the sum of the weight of the sled plus the weight of the person:
W = 52 N + 700 N = 752 N
Then:
N = 752 N
Fr = 0.11 · 752 N
Fr = 83 N
Then
F = 83 N
A force of 83 N is needed to pull the sled with constant speed.
Lean more:
brainly.com/question/18038995
What is a geologist’s role in the petroleum industry? stay with the drillers to examine rock and fossils brought to the surface chart information on a well log calculate the distance and direction of movement of the lost vein of ore locate environments in which petroleum forms
Answer:what is the role of of geologist in the petroleum industry
A. Stay with the drillers to examine rocks and fossils brought to the surface.
B. Chart information on a well log
C. Calculate the distance and direction of movement of the lost vein of ore
D. locate environment in which the petroleum forms
Correct option. Is D locate environment in which petroleum forms
Explanation:
Petroleum geologists are usually linked to the actual discovery of oil and the identification of possible oil deposits or leads. It can be a very labor-intensive task involving several different fields of science and elaborate equipment. Petroleum
geologists look at the structural and
sedimentary aspects of the stratum/strata to identify possible oil traps
Answer: D locate environment in which the petroleum forms
Explanation:
Which of the following statements are true. (Justify your answer to get credit) (5 points)
1. Mechanical energy is conserved before and after the string is cut.
2. Mechanical energy is conserved before the string is cut.
3. Mechanical energy is conserved after the string is cut
4. Linear momentum is conserved 5. Angular momentum is conserved.
Answer:
2 & 3
Explanation:
Since they are all vector quantities, if they remain in a closed system where no external force acts on the system, the vector sum of the momentum remains constant.
When there is no loss or gain in the total vector sum of the energy of the system means it's energy is conserved.
Scientists who wished to study the metabolic function of cells with balanced translocations while preventing cell replication would be best served by arresting the cells during which phase of the cell cycle?
Answer:
Interphase.
Explanation:
interphase
When scientists were to prevent cell duplication, they would have to interrupt the division of cells (mitosis). Interphase is the stage of the cell life cycle that occur in between cell dividing stages.
It is during this phase that preventing cell replication would be best served by arresting the cells.
A novice skier, starting from rest, slides down a frictionless 29.0∘ incline whose vertical height is 185 mm. How fast is she going when she reaches the bottom?
Answer:
Her speed when she reaches the bottom of the incline is 1.90 m/s.
Explanation:
Hi there!
To solve this problem, let´s use the energy conservation theorem:
Initially, the skier is at rest at a height of 0.185 m. Since she is at rest, her kinetic energy will be zero and her gravitational potential energy (PE) will be:
PE = m · g · h
Where
m = mass of the skier.
g = acceleration due to gravity.
h = height.
When she reaches the bottom, the height is zero and then the potential energy will be zero. Since there is no friction, the initial potential energy had to be converted into kinetic energy because the total energy of the skier remains constant, i.e., it is conserved.
Then, the final kinetic energy (KE) of the skier has to be equal to the initial potential energy:
PE = KE
The equation of kinetic energy is the following:
KE = 1/2 · m · v²
Then:
KE = PE
1/2 · m · v² = m · g · h
1/2 · m · v² = m · 9.8 m/s² · 0.185 m
v² = 2 · 9.8 m/s² · 0.185 m
v = 1.90 m/s
Her speed when she reaches the bottom of the incline is 1.90 m/s.
A falling object of weight 10 N encounters 10 N of air resistance. The net force on the object is____________.
An object of weight 10 N that is falling on the ground, and it experiences a 10 N air resistance, then the net force on the object will be 0 N.
What is Force?A force in physics is an input that has the power to change an object's motion.
A mass-containing object's velocity can vary, or accelerate, as a result of a force. Intuitively, a push or a pull can also be used to describe forces. Being such a vector quantity, a force does have magnitude and direction. The SI unit metric newton is used to measure it (N). The letter F stands for force.
According to Newton's second law's original formulation, an object's net force is equal to the speed that its momentum is changing over time.
As per the given information in the question,
Weight of the object = 10 N
Friction due to air resistance = 10 N
Then, the net force will be,
10 N - 10 N = 0 N
Therefore, the net force will be 0 N.
To know more about Force:
https://brainly.com/question/13191643
#SPJ5
The net force on the object is zero.
When an object is falling, it experiences two main forces: gravity (its weight) pulling it downward and air resistance pushing upward. In this case, the object has a weight of 10 N (newtons), which is a force acting downward due to gravity, and it encounters 10 N of air resistance, which is a force acting upward against the motion of the falling object.
To find the net force on the object, you need to calculate the difference between the two forces:
Net Force = Weight - Air Resistance
Net Force = 10 N - 10 N
Net Force = 0 N
So, the net force on the object is 0 N. This means that the forces of gravity and air resistance are equal in magnitude and opposite in direction, resulting in a net force of zero. In this situation, the object is in a state of dynamic equilibrium, and its velocity remains constant (it doesn't accelerate further).
Learn more about net force here:
https://brainly.com/question/14361879
#SPJ3
Julie runs 2 miles every day after school because it reduces the stress she feels from schoolwork. Julie's running habit is maintained by a ________ reinforcer.
Answer:
negative
Explanation:
The term reinforce means to strengthen, and is used in psychology to refer to any stimulus which strengthens or increases the probability of a specific response.
Negative Reinforcement can be seen as the act of taking something negative away in order to increase a response.
Julie runs 2 miles every day after school because it reduces the stress (negative) she feels from school work (in order to increase her response in her school work).
Two neutral metal spheres on wood stands are touching. A negatively charged rod is held directly above the top of the left sphere, not quite touching it. While the rod is there, the right sphere is moved so that the spheres no longer touch. Then the rod is withdrawn. Afterward, what is the charge state of each sphere? Use charge diagrams to explain your answer.
A. Both the spheres are neutral.
B. The left sphere is negatively charged, the right sphere is charged positively.
C. The right sphere is negatively charged, the left sphere is charged positively.
D. Both the spheres are charged positively.
E. Both the spheres are charged negatively.
Answer:
The right sphere is negatively charged, the left sphere is charged positively.
Explanation:
When a negatively charged rod is held above the top of left sphere, the rod will attract positive charges and repel negative charges. As the sphere are initially touching each other so positive charges from the both spheres will moves toward the rod. When we separate the spheres positive charges from right sphere have already moved toward the rod i.e. left sphere, creating a deficiency of positive charges in the right sphere and excessiveness of positive charges in left sphere , hence the right sphere will remain negatively charged and left sphere will remain positively charged.
An autotransformer is used to reduce the voltage of a 100-kilovolt amp, 480-volt secondary of an isolated type transformer, to supply a 100-kilovolt amp load with 277 volts. What size autotransformer is needed? (Use the co-ratio to determine the size.)
An autotransformer is a type of electrical transformer that has only one winding, and portions of the same winding act as both the primary and secondary winding sides of the transformer. A 33.9 kVA autotransformer is needed to reduce the voltage of a 100-kilovolt amp, 480-volt secondary of an isolated type transformer to supply a 100-kilovolt amp load with 277 volts, using the co-ratio method.
To determine the size of an autotransformer needed to reduce the voltage of a 100-kilovolt amp, 480-volt secondary of an isolated type transformer to supply a 100-kilovolt amp load with 277 volts, we can use the co-ratio method.
The co-ratio is the ratio of the number of turns on the primary winding to the number of turns on the secondary winding of the transformer.
Secondary voltage: 480 V
Load voltage: 277 V
Load current: 100 kVA
To calculate the co-ratio, we can use the formula:
Co-ratio = Secondary voltage / Load Voltage
Co-ratio = 480 V / 277 V
Co-ratio ≈ 1.734
The co-ratio is approximately 1.734. To determine the size of the autotransformer needed, we can use the formula:
Size of autotransformer = Load kVA / (Co-ratio)²
Size of autotransformer = 100 kVA / (1.734)²
Size of autotransformer ≈ 33.9 kVA
Therefore, a 33.9 kVA autotransformer is needed to reduce the voltage of a 100-kilovolt amp, 480-volt secondary of an isolated type transformer to supply a 100-kilovolt amp load with 277 volts, using the co-ratio method.
To know more about autotransformers:
https://brainly.com/question/34694881
#SPJ12
To supply a 100 kilovolt-ampere load with 277 volts from a 480-volt secondary, an autotransformer that is roughly 1.73 times smaller than the original isolated type transformer is required. The size calculation is derived from the co-ratio (the ratio of primary to secondary voltages), which here equals to 480/277 = 1.73.
Explanation:The subject in question is regarding the use of an autotransformer, specifically, what size is needed to reduce the voltage from 480 volts to 277 volts in order to supply a 100 kilovolt-ampere load. First, we need to handle the co-ratio. The co-ratio of a transformer is the ratio of primary to secondary voltages, often used to calculate the size of a transformer. In this case the co-ratio would be 480/277 = 1.73.
Utilizing the transformer equation, we can comprehend that the voltage reduction from 480 to 277 volts that undergoes in an autotransformer proposes a comparable reduction in size of the transformer. Based on this, the autotransformer needed should be around 1.73 times smaller than the original isolated type transformer.
As a brief primer on the functioning of the transformers, they operate on the principle of electromagnetic induction and are used in power distribution systems to step-up or step-down the voltages. This allows the efficient transmission of power over long distances and also the provision of the correct voltage levels suitable for different uses.
Learn more about Transformers and Autotransformer Sizing here:https://brainly.com/question/32456416
#SPJ12
why doesnt the moon get pulled into the sun
Answer:
The moon does not get pulled into the sun because of gravitational pull.
Explanation:
Gravitational pull is a force that pulls things down or into i guess you can say. Like are orbit, all of the planets (even the dwarf planet "pluto") are circling around are sun but we have things called moons that circle are planets. Are moon is orbiting us like we (are earth) are orbiting the sun. So to get into a little more detail, i will add that we circle the sun or the moon circles us because the action of earth pulling away from the suns gravitational pull is causing it to either rotate or revolve.So we are stuck in the gravitational force of the sun and the moon is stuck in ares. But as someone who LOVES astronamy will say that i watched a video about are earth, sun, and moon and it said that each year are moon is slowly pulling away from the earth. sooner or later we might not have a solar or lunar eclipse anymore.
Answer:
But the path of the Moon is always concave towards the Sun; the gravitational force exerted by the Sun on the Moon is always greater than the pull of the Earth on the Moon
Explanation:
A ski jumper has 1.2 x 10 4 J of potential energy at the top of the ski jump. The friction on the jump slope is small, but not negligible. What can you conclude about the ski jumpers kinetic energy at the bottom of the jump?
Answer
kinetic energy will be less than 1.2×10^4 J
Explanation:
as some of this potential energy will be used to over come force of friction , hence by law of conservation of energy , kinetic energy will be less than potential energy at top and will be less than 1.2×10^4 J
Final answer:
The ski jumper's kinetic energy at the bottom of the ski jump will be slightly less than the initial potential energy of 1.2 x 10⁴ J due to the small but non-negligible work done by friction, which converts some of the mechanical energy into other forms like heat and sound.
Explanation:
If a ski jumper has 1.2 x 10⁴ J of potential energy at the top of the ski jump and we take into account that friction is small but not negligible, we can conclude that the ski jumper's kinetic energy at the bottom will be slightly less than 1.2 x 10⁴ J. According to the conservation of energy principle, the sum of potential and kinetic energy in a system should be constant if there is no external work done. However, friction does perform negative work (it removes energy from the system), converting some mechanical energy into heat and sound, and therefore the actual kinetic energy at the bottom will be the initial potential energy minus the energy lost due to friction.
For example, in the given scenario where a ski jumper starts from rest, their initial kinetic energy is zero, and all the energy is in the form of potential energy. As they descend, potential energy is converted into kinetic energy. When friction is present, it will do negative work on the system, represented by a slight decrease in the total mechanical energy by the time the skier reaches the bottom. The kinetic energy of the ski jumper at the bottom would be the initial potential energy minus the work done by friction during the descent.
In a theoretical scenario without friction, the skier's kinetic energy at the bottom would equal their initial potential energy minus zero (since no work is done by friction), resulting in the skier having kinetic energy equal to 1.2 x 10⁴ J at the bottom.
The multi-link mechanism in the Variable Compression Turbo Engine _____, thus varying the compression ratio.
A. Adjusts how far down the piston travels
B. Can change one individual piston's operation independent of the other three
C. Acts like a fixed-length connecting rod
Answer:
A. Adjusts how far down the piston travels
Explanation:
This type of engine changes the possition of the piston in order to modify the compression chamber volume and therefore the compression ratio of the engine. The volume of the chamber is proportional to the run of the piston (how far down the piston travels)
This engine is used to achive the optimal compression rate in each individual stage.
The multi-link mechanism in a Variable Compression Turbo Engine adjusts the piston travel to vary the compression ratio, providing efficient operation under different conditions but does not change individual pistons independently.
The multi-link mechanism in the Variable Compression Turbo Engine adjusts the angle of the connecting rods, which in turn adjusts how far down the piston travels in the cylinder. This adjustment changes the volume of the cylinder when the piston is at the top of its stroke, thus varying the compression ratio. The multi-link mechanism does not act like a fixed-length connecting rod nor can it change one individual piston's operation independent of the others, as all pistons in a multi-cylinder engine are generally interconnected and move synchronously.
By varying the compression ratio, the engine can operate efficiently under a variety of conditions, offering more power when needed or improving fuel efficiency when less power is required. This mechanism is a sophisticated mechanical linkage that transforms the linear motion of the pistons into the rotary motion of the crankshaft, similar to the operation of conventional connecting rods, but with the added capability of adjusting the compression ratio.
Two speakers are spaced 15 m apart and are both producing an identical sound wave. You are standing at a spot as pictured. What would be the frequency produced by the speakers to create perfectly constructive interference? Assume n = 1 and v = 343 m/s
213.04 Hz
256.70 Hz
186.68 Hz
233.14 Hz
Answer:
213.04
Explanation:
Answer:
The correct answer is option 213.04 Hz
Explanation:
Hello!
Let's solve this!
In this link we will find the image of the problem.
https://smart-answers.com/physics/question14138735
Regarding that image, we will first calculate the distance from my position to S1 and then to S2. Then the difference between these results.
We will use pitagoras.
S1 = [tex]\sqrt{10^{2}+22^{2} }[/tex]
S1 = 24.17
S2 = [tex]\sqrt{5^{2}+22^{2} }[/tex]
S2 = 22.56
The difference will be:
24.17-22.56 = 1.61 m
Constructive interference:
Δr=n*λ
λ=1.61 m (for n = 1)
Then we will calculate the frequency:
f = v / λ
f = (343m / s) /1.61m
f = 213.04 Hz
So the correct answer is option 213.04 Hz
A horse draws a sled horizontally across a snow-covered field. The coefficient of friction between the sled and the snow is 0.135, and the mass of the sled, including the load, is 195.9kg. If the horse moves the sled at a constant speed of 1.785m/s, what is the power needed to accomplish this?
Answer:
P = 462.62 watts
Explanation:
The power needed to accomplish this can be calculated how
P = Fv
Where F: The force exerted by the horse
v: velocity
The force exerted by the horse is against friction force; how the movement is with constant velocity these forces must be equals, then
Fr = μN
=μmg
= (0.135)(195.9)(9.8)
= 259.17 N
And the power is
P = (259.17)(1.785)
P = 462.62 watts
The power needed to accomplish this is 462.62 watts.
What is the coefficient of friction?It is defined as the numerical value that indicates the amount of friction present between the surfaces of two bodies. The lower the coefficient of friction the lower the friction between the surfaces and the higher coefficient of friction the higher the friction force between them.
We know the:
P = F×v
Where P is the power needed to accomplish this.
F = force exerted by the horse
v = velocity of the horse.
For F = [tex]\rm \mu N[/tex]
[tex]\mu = 0.135[/tex]
N = mg ⇒ 195.9×9.8 ( m= 195.9 kg and g = 9.8 [tex]\rm m/sec^2[/tex])
N = 1919.82 Newtons
F = 0.135×1919.82 ⇒ 259.1757 Newtons
Now P = F×v ⇒259.1757×1.785
P = 462.62 Watts
Thus, the power needed to accomplish this is 462.62 watts.
Learn more about the coefficient of friction here:
https://brainly.com/question/13828735
An adult generates 72 W of power as she pulls a sled forward across a flat snowy surface with a force of 80 N. The adult pulls with this force for 4.5 minutes. What distance does the sled move?
130 m
280 m
240 m
180 m
Answer:
240 m
Explanation:
Gradpoint
Final answer:
To calculate the distance the sled moves, use the formula Work = Force x Distance and substitute the given values to find the answer as 240 meters.
Explanation:
Power is a physical quantity that represents the rate at which work is done or energy is transferred or converted. Mathematically, power is defined as the amount of energy transferred or converted per unit time. It is typically measured in watts (W), where 1 watt is equivalent to 1 joule per second. In other words, power indicates how quickly work is done or energy is transferred.
To find the distance the sled moves, we can use the formula:
Work = Force x Distance
Given: Power = 72 W, Force = 80 N, Time = 4.5 minutes = 270 seconds
Work = Power x Time = 72 W x 270 s = 19440 J
Distance = Work / Force = 19440 J / 80 N = 243 m
Therefore, the sled moves a distance of 240 meters.
When driving through standing water at high speed water may build up beneath the wheels and cause the vehicle to skid is commonly referred to as:________
Answer: Hydroplaning
Explanation: Hydroplaning is the skiding of a high speed vehicle when water builds beneath the wheels when driving through standing water.
It is usually caused by factors such as High speed,Standing water,deflated tyres. It is strongly recommended that when driving in standing water a driver should drive at a slow and steady speed and always to ensure that the vehicle tyres are adequately inflated with air,this is one of the causes of vehicular accidents during rainy season or flood.
What is the specific fuel requirement for flight under VFR at night in an airplane?
A) Enough to fly to the first point of intended landing and to fly after that for 45 minutes at normal cruising speed.
B) Enough to complete the flight at normal cruising speed with adverse wind conditions.
C) Enough to fly to the first point of intended landing and to fly after that for 30 minutes at normal cruising speed.
Answer:
A). Enough to fly to the first point of intended landing and to fly after that for 45 minutes at normal cruising speed
Explanation:
Here are Fuel requirements for flight in VFR conditions
No person may begin a flight in an airplane under VFR conditions unless there is enough fuel to fly to the first point of intended landing and, assuming normal cruising speed -
During the day, to fly after that for at least 30 minutes; or At night, to fly after that for at least 45 minutes.You throw a ball straight up, it peaks out, and then cones back down to you. During this motion, the velocity and acceleration
a) always point in the same direction
b) always point in opposite direction
c) sometimes point in the same direction, and other times point in opposite to each other.
d) depends on the way the ball is thrown
e) depends in the mass of the ball
Answer:
The answer is C sometimes point in the same direction, and other times point in opposite to each other.
Explanation:
When you throw a ball straight up velocity direction head up to up side but the acceleration points opposite direction due to gravitation of earth. Gr aviation slows down the ball when it goes up, when it reaches the summit and starts to fall down both velocity and acceleration points the same way. The ball speeds up and drops down.
The velocity and acceleration of a ball thrown straight up sometimes point in the same direction and sometimes in opposite directions. On the way up, they are opposite, but when the ball peaks and begins falling, they align in the same direction (downward). Therefore, the correct answer is that they sometimes point in the same direction and other times in opposite directions.
Explanation:When you throw a ball straight up, it follows a parabolic trajectory due to the influence of gravity. Let's examine the ball's velocity and acceleration throughout its motion:
The ball's velocity is initially positive as it travels upwards after being thrown. When the ball reaches its highest point, its velocity becomes zero as it changes direction.From the moment the ball is released until it hits the ground, the acceleration due to gravity is a constant negative value, directed downward toward the center of the Earth.On the way up, the direction of the ball's velocity (upward) and the direction of acceleration (downward) are opposite. When the ball reaches its peak and starts to fall back down, the velocity (now downward) and the constant acceleration due to gravity (also downward) will be in the same direction.Therefore, during the motion of the ball, the acceleration does not always point in the same direction as the ball's motion. Instead, the direction of velocity and acceleration are opposite on the ascent and the same on the descent. Hence, our answer to the question is that the velocity and acceleration sometimes point in the same direction, and other times point in opposite to each other.
The basal metabolic rate is the rate at which energy is produced in the body when a person is at rest. A 71 kg ( 157 lb ) person of height 1.75 m (5.7 ft ) would have a body surface area of approximately 1.90 m².
What is the net amount of heat this person could radiate per second into a room at 19.0 °C (about 66.2 °F) if his skin's surface temperature is 30.0 °C? (At such temperatures, nearly all the heat is infrared radiation, for which the body's emissivity is 1.0, regardless of the amount of pigment.)
Answer:
125.04181 W
Explanation:
[tex]\sigma[/tex] = Stefan-Boltzmann constant = [tex]5.67\times 10^{-8}\ W/m^2K^4[/tex]
A = Surface area = 1.9 m²
[tex]T_b[/tex] = Skin surface temperature = 19°C
[tex]T_s[/tex] = Room temperature = 30°C
[tex]\epsilon[/tex] = Emissivity = 1
Radiated thermal energy is given by
[tex]P=\epsilon A\sigma (T_b^4-T_s^4)\\\Rightarrow P=1\times 1.9\times 5.67\times 10^{-8}((273.15+30)^4-(273.15+19)^4)\\\Rightarrow P=125.04181\ W[/tex]
The net amount of heat this person could radiate per second into the room is 125.04181 W
You have purchased a new 20-pin power supply to replace one that failed. However, the motherboard only has a 24-pin connector. What should you do?
This question is incorrect.The correct question is here
You have purchased a new 24-pin power supply to replace one that failed. However, the motherboard only has a 20-pin connector. What should you do?
Answer:
To solve this problem you should plug the 24-pin power supply into the motherboard, as your mother board has 20 pin you leave pins 11, 12, 23, and 24 on the motherboard unconnected.
I have attached a picture from which you can see that there are pins for same working
Suppose that a person riding on the top of a freight car shines a searchlight beam in the direction in which the train is traveling.
How does the speed of the light beam relative to the ground compare to the speed of beam when the train is at rest?
Answer:
same
Explanation:
Acc. to Einstien's postulate of special theory of
Relativity , Velocity of the light beam is same in all frames of references
(a) If the freight car is at rest
The frame we can assumed as Non - inertial frame of reference s
In the inertial frame of reference , velocity of the light beam has its own value as : 3 x 10^8 m/s
(b) If the freight car is moving , the frame we can assumed as Non -inertial frame of reference
In thus case also , The velocity of the light beam will also have the same value as ; 3 x 108 m/s
As a way of determining the inductance of a coil used in a research project, a student first connects the coil to a 9.7 V battery and measures a current of 0.742 A. The student then connects the coil to a 27.3 V(rms), 51.1 Hz generator and measures an rms current of 0.429 A. What is the inductance?
Answer:
L = 0.194 H
Explanation:
given,
Voltage = 9.7 V
current = 0.742 A
R = 9.7 V / 0.742 A
R = 13.07 Ohms.
the A.C. impedance of the inductor, like this:
Z = V / I
Z = 27.3 V / 0.429 A
Z = 63.64 Ohms.
now,
inductive reactance, X_L
[tex]X_L = \sqrt{Z^2 - R^2}[/tex]
[tex]X_L = \sqrt{63.64^2 - 13.07^2}[/tex]
[tex]X_L =62.28\ \Omega[/tex]
[tex]X_L = 2\pi f \times L[/tex]
[tex]L = \dfrac{X_L}{2\pi f}[/tex]
[tex]L = \dfrac{62.28}{2\pi \times 51.1}[/tex]
L = 0.194 H
Suppose we imagine the Sun to be about the size of a grapefruit. How big an area would the orbits of the nine planets of the Solar System cover?
Answer:
size at this scale of the solar system is 10⁸ m²
Explanation:
For this exercise we can use a direct proportions rule or rule of three.
If the radius of the Sun is 7 10⁸ m is equal to the radius of a grapefruit is on average about 5 cm, the radius of the orbit of the plant is x
Mercury
r1 = 5.8 10¹⁰m
x = r1 / r_Sum 5
x = 5.8 10¹⁰/7 10⁸
x = 82 m
We repeat the same formula with all the radii of the orbit, the results in the table
Numb name r_orbit (m) x (m) A (m2)
0 Sun 7 10⁸ 1 3.14
1 mercury 5.8 10¹⁰ 8.2 10¹ 2.0 10⁴
2 venus 1 10¹¹ 1.4 10² 6.2 10⁴
3 Earth 1.5 10¹¹ 2.1 10² 1.4 10⁵
4 Mars 2.3 10¹¹ 3.2 10² 3.2 10⁵
5 Jupiter 7.8 10¹¹ 1.1 10³ 3.8 10⁶
6 Saturn 1.4 10¹² 2 10³ 1.3 10⁷
7 Uranus 2.9 10¹² 4.1 10³ 5.3 10⁷
8 Neptune 4.5 10¹² 6.4 10³ 1.3 10⁸
9 Pluto 5.9 10¹² 8.4 10³ 2.2 10⁸
The area of a circle is
A = π R²
Mercury
A = π 80²
A = 2.0 14 m²
The other values are in the table
The size at this scale of the solar system is 10⁸ m²