Answer:
S°m,298K = 85.184 J/Kmol
Explanation:
∴ T = 10 K ⇒ Cp,m(Hg(s)) = 4.64 J/Kmol
∴ 10 K to 234.3 K ⇒ ΔS = 57.74 J/Kmol
∴ T = 234.3 K ⇒ ΔHf = 2322 J/mol
∴ 234.3 K to 298.0 K ⇒ ΔS = 6.85 J/Kmol
⇒ S°m,298K = S°m,0K + ∫CpdT/T(10K) + ΔS(10-234.3) + ΔHf/T(234.3K) + ΔS(234.3-298)
⇒ S°m,298K = 0 + 10.684 J/Kmol + 57.74 J/Kmol + 9.9104 J/Kmol + 6.85 J/kmol
⇒ S°m,298K = 85.184 J/Kmol
To find the Third-Law standard molar entropy of Hg(l) at 298 K, we sum up the entropy changes between 10K and 234.3 K, the entropy change due to fusion, and then the entropy change between the melting point and 298K. The sum gives us a final value of 74.51 J K−1 mol−1.
Explanation:The Third-Law standard molar entropy of Hg(l) at 298 K can be calculated by summing up the entropy changes that occur from 10K to 298K.
First calculate the entropy up to the melting point from 10 K which can be determined using the equation ΔS = ∫(Cp,mdT)/T.
This integral can be approximated as a rectangle from 10K to 234.3 K, hence ΔS₁ = (234.3-10)(4.64 J K−1 mol−1)/10 = 57.74 J K−1 mol−1.
Next, calculate the entropy change associated with the fusion process using the equation, ΔS = ΔH/T, giving ΔS₂ = 2322 J mol−1 / 234.3 K = 9.92 J K−1 mol−1.
Finally, add the entropy increase from the melting point to 298.0 K, which is given as 6.85 J K−1 mol−1.
Summing these values gives the Third-Law standard molar entropy of Hg(l) at 298 K: 57.74 J K−1 mol−1 + 9.92 J K−1 mol−1 + 6.85 J K−1 mol−1 = 74.51 J K−1 mol−1.
Learn more about Third-Law Standard Molar Entropy here:https://brainly.com/question/31964560
#SPJ11
The heating curve for a sample of pure ethanol shows the slope of the line for gaseous state is greater than the slope of the line for the liquid state.
Which statement below explains that?a. The specific heat capacity of the gaseous ethanol is less than the specific heat capacity of liquid ethanol.b. The specific heat capacity of the gaseous ethanol is greater than the specific heat capacity of liquid ethanol.c. The heat of vaporization of ethanol is less than the heat of fusion of ethanol.d. The heat of vaporization of ethanol is greater than the heat of fusion of ethanol.
Answer:
a. The specific heat capacity of the gaseous ethanol is less than the specific heat capacity of liquid ethanol.
Explanation:
The heating curve is a curve that represents temperature (T) in the y-axis vs. added heat (Q) in the x-axis. The slope is T/Q = 1/C, where C is the heat capacity. Then, the higher the slope, the lower the heat capacity. For a constant mass, it can also represent the specific heat capacity (c).
Heats of vaporization and fusion cannot be calculated from these sections of the heating curve.
Which statement below explains that?
a. The specific heat capacity of the gaseous ethanol is less than the specific heat capacity of liquid ethanol. YES.
b. The specific heat capacity of the gaseous ethanol is greater than the specific heat capacity of liquid ethanol. NO.
c. The heat of vaporization of ethanol is less than the heat of fusion of ethanol. NO.
d. The heat of vaporization of ethanol is greater than the heat of fusion of ethanol. NO.
The correct option is b. The specific heat capacity of the gaseous ethanol is greater than the specific heat capacity of liquid ethanol.
To understand why option b is correct, let's consider the heating curve for ethanol and what the slope of the line represents. The slope of the line on a heating curve indicates the rate at which the temperature of the substance increases per unit of heat added. A steeper slope means that the temperature rises more quickly for a given amount of heat.
In the context of the heating curve for ethanol:
- The slope of the line for the gaseous state is steeper than the slope for the liquid state. This means that for the same amount of heat added, the temperature of gaseous ethanol increases more than the temperature of liquid ethanol.
- The specific heat capacity (c) of a substance is the amount of heat required to raise the temperature of one gram of the substance by one degree Celsius. A higher specific heat capacity means that more heat is required to achieve the same temperature change.
Now, let's analyze the options:
a. The specific heat capacity of the gaseous ethanol is less than the specific heat capacity of liquid ethanol. - This would mean that gaseous ethanol requires less heat to increase its temperature by a certain amount compared to liquid ethanol. However, the steeper slope for the gaseous state indicates that it takes more heat to increase the temperature of the gas by a certain amount, not less. Therefore, this option is incorrect.
b. The specific heat capacity of the gaseous ethanol is greater than the specific heat capacity of liquid ethanol. - This is consistent with the observation that the temperature of the gas increases more slowly than that of the liquid for the same amount of heat added (as indicated by the steeper slope for the gas). Since the gas requires more heat to increase its temperature, it has a higher specific heat capacity. This option is correct.
c. The heat of vaporization of ethanol is less than the heat of fusion of ethanol. - The heat of vaporization is the amount of heat required to change a substance from the liquid to the gaseous state, while the heat of fusion is the amount of heat required to change a substance from the solid to the liquid state. This option is incorrect because the heat of vaporization is typically much greater than the heat of fusion for most substances, including ethanol.
d. The heat of vaporization of ethanol is greater than the heat of fusion of ethanol. - This statement is generally true for most substances, including ethanol. However, it does not explain the difference in slopes between the gaseous and liquid states on the heating curve. The heat of vaporization is related to the amount of heat required to change the phase of the substance, not the rate at which the temperature changes within a given phase. Therefore, this option is not relevant to the explanation of the slopes on the heating curve.
In conclusion, the correct explanation for the observation that the slope of the line for gaseous ethanol is greater than the slope for liquid ethanol is that the specific heat capacity of gaseous ethanol is greater than that of liquid ethanol. This means that more heat is required to raise the temperature of the gas by a certain amount compared to the liquid, which is consistent with the steeper slope on the heating curve for the gaseous state.
Bobby found that water has a high boiling point and concluded this was because water has weak intermolecular forces. Based on the data, is Bobby’s conclusion correct? A. Yes, because polar covalent molecules have weaker intramolecular forces than nonpolar covalent molecules. B. Yes, because polar covalent molecules have weaker intermolecular forces than nonpolar covalent molecules. C. No, because polar covalent molecules have stronger intramolecular forces than nonpolar covalent molecules. D. No, because polar covalent molecules have stronger intermolecular forces than nonpolar covalent molecules.
Answer:
(D.) No, because polar covalent molecules have stronger intermolecular forces than nonpolar covalent molecules.
Explanation:
In water molecules intermolecular hydrogen bonding occurs between hydrogen and highly electronegative elemnt oxygen that increases the intermolecular forces. Hence water has high boiling point.
Answer:
D. No, because polar covalent molecules have stronger intermolecular forces than nonpolar covalent molecules.
Explanation:
Hello,
Intermolecular forces are those which attract or repel molecules to, or from each other. In this case, since water is the involved molecule, it is known that it is a polar covalent one, as the difference between the electronegativities of oxygen and hydrogen is 1.24, in this manner, it is also known that the more polar the molecule is, the stronger its intermolecular forces are are they are tend to stick the molecules. In such a way, the answer is: D. No, because polar covalent molecules have stronger intermolecular forces than nonpolar covalent molecules.
Best regards.
According to the following reaction, how many grams of potassium phosphate will be formed upon the complete reaction of 29.6 grams of phosphoric acid with excess potassium hydroxide? 3KOH(aq)+H3PO4(aq) <=>K3PO4(aq)+3H2O(l)
Upon the complete reaction of 29.6 grams of phosphoric acid with excess potassium hydroxide, approximately 64 grams of potassium phosphate will be produced.
Explanation:To determine the amount of potassium phosphate that will be produced, we first need to find the molar mass of phosphoric acid (H3PO4), which is approximately 98 g/mol. So, 29.6 grams of phosphoric acid is equal to 0.302 moles (29.6g / 98g/mol).
The balanced equation shows that each mole of phosphoric acid will produce one mole of potassium phosphate (K3PO4) in the reaction. Therefore, 0.302 moles of phosphoric acid will produce 0.302 moles of potassium phosphate.
Next, we need to convert this amount from moles to grams. The molar mass of potassium phosphate is roughly 212 g/mol. So, 0.302 moles of K3PO4 is equal to approximately 64 grams (0.302 moles * 212 g / mol).
Therefore, upon the complete reaction of 29.6 grams of phosphoric acid with excess potassium hydroxide, approximately 64 grams of potassium phosphate will be formed.
Learn more about Stoichiometry here:https://brainly.com/question/30218216
#SPJ3
There are 7.11 x1024molecules in 100.0 cm3of a certain substance.a. What is the number of molecules in 1.09 cm3of the substance?7.75 x 1022moleculesb.What is the number of molecules in 2.24 x 104cm3of the substance?1.59 x 10 27moleculesc. What number of molecules would be in 9.01 x 10-6cm3?6.41 x 1017molecules
Answer:
a. 7.75 × 10²² molecules
b. 1.59 × 10²⁷ molecules
c. 6.41 × 10¹⁷ molecules
Explanation:
There are 7.11 × 10²⁴ molecules in 100.0 cm³ of a certain substance. We will use this ratio in our conversion fractions.
a. What is the number of molecules in 1.09 cm³ of the substance?
1.09 cm³ × (7.11 × 10²⁴ molecules/100.0 cm³) = 7.75 × 10²² molecules
b. What is the number of molecules in 2.24 × 10⁴ cm³ of the substance?
2.24 x 10⁴ cm³ × (7.11 × 10²⁴ molecules/100.0 cm³) = 1.59 × 10²⁷ molecules
c. What number of molecules would be in 9.01 × 10⁻⁶ cm³?
9.01 × 10⁻⁶ cm³ × (7.11 × 10²⁴ molecules/100.0 cm³) = 6.41 × 10¹⁷ molecules
Calculating the number of particles in a given volume involves using Avogadro's number and proportionality between the volume and the number of particles, assuming constant density.
Explanation:The question involves concepts from chemistry, specifically dealing with Avogadro's number, the mole, and calculations of the number of molecules in a given volume. Avogadro's number is defined as the number of atoms or molecules in one mole of a substance, which is 6.022 × 10²23. When given the number of molecules in a specific volume, you can calculate the number of molecules in a different volume by setting up a proportional relationship. This is because the number of molecules is directly proportional to the volume if the density remains the same.
For example, if there are 7.11 × 10²24 molecules in 100.0 cm³ of a substance, to find the number of molecules in 1.09 cm³:
Set up a proportion: (7.11 × 10²24 molecules / 100 cm³) = (x molecules / 1.09 cm³)Solve for x to find the number of molecules in 1.09 cm³.Similarly, you would use the same approach for other volumes to determine the number of molecules in 2.24 × 10²4 cm³ and 9.01 × 10²²6 cm³ respectively.
A chemist designs a galvanic cell that uses these two half-reactions: half-reaction standard reduction potential (s)(aq)(aq)(l) (aq)(aq) Answer the following questions about this cell. Write a balanced equation for the half-reaction that happens at the cathode. Write a balanced equation for the half-reaction that happens at the anode. Write a balanced equation for the overall reaction that powers the cell. Be sure the reaction is spontaneous as written. Do you have enough information to calculate the cell voltage under standard conditions
Answer:
Reduction (cathode): Cu²⁺(⁺aq) + 2 e⁻ → Cu(s)
Oxidation (anode): Zn(s) → Zn²⁺(⁺aq) + 2 e⁻
Cu²⁺(⁺aq) + Zn(s) → Cu(s) + Zn²⁺(⁺aq)
E°cell = 1.10 V
Explanation:
The half-reactions are missing, but I will propose some to show you the general procedure and then you can apply it to your equations.
Suppose we have the following half-reactions.
Cu²⁺(⁺aq) + 2 e⁻ → Cu(s) E°red = 0.34 V
Zn²⁺(⁺aq) + 2 e⁻ → Zn(s) E°red = -0.76 V
To identify how to make a spontaneous cell, we need to consider the standard reduction potentials (E°red). The half-reaction with the higher E°red will occur as a reduction (in the cathode), whereas the one with the lower E°red will occur as an oxidation (in the anode).
Reduction (cathode): Cu²⁺(⁺aq) + 2 e⁻ → Cu(s) E°red = 0.34 V
Oxidation (anode): Zn(s) → Zn²⁺(⁺aq) + 2 e⁻ E°red = -0.76 V
To get the overall equation we add both half-reactions.
Cu²⁺(⁺aq) + Zn(s) → Cu(s) + Zn²⁺(⁺aq)
The standard cell potential (E°cell) is the difference between the standard reduction potential of the cathode and the standard reduction potential of the anode.
E°cell = E°red, cat - E°red, an
E°cell = 0.34 V - (-0.76 V) = 1.10 V
Since E°cell > 0, the reaction is spontaneous.
With the provided half-reactions information, one could write the reduction and oxidation reactions at the cathode and anode, respectively, and determine the overall balanced equation for the spontaneous redox reaction in a galvanic cell. The positive and negative electrodes, identifying the cathode and anode, play a key role in this determination. However, without the specific details of the half-reactions, it's not possible to write the balanced equations or calculate the cell voltage.
Explanation:To answer questions about the galvanic cell, we require specifics about the half-reactions involved. The half-reaction that occurs at the cathode is the reduction process, and the half-reaction that occurs at the anode is the oxidation process. However, without the actual half-reactions or the substances involved, it is impossible to write the precise equations.
In general terms, if the half-reactions and their respective standard reduction potentials are known, we can write the reactions as follows:
Cathode (Reduction): A⁺⁺+(aq) + ne⁻ → A(s) (where n is the number of electrons transferred)Anode (Oxidation): B(s) → B⁺⁺+(aq) + ne⁻The electrode at which reduction occurs, the cathode, is the positive electrode, while the electrode at which oxidation occurs, the anode, is the negative electrode. For the overall balanced equation that powers the cell, simply combine the two half-reactions to get the full-cell reaction.
To calculate the cell voltage under standard conditions, the difference in standard electrode potentials between the cathode and anode is taken (E°cathode - E°anode). The overall reaction should be spontaneous if the cell voltage is positive.
Learn more about Galvanic Cell here:https://brainly.com/question/32505497
#SPJ3
What is the angle between two of the nitrogen-hydrogen bonds in the ammonium (NH4+) ion?
Answer:
109° 27'
Explanation:
The ammonium ion is tetrahedral in shape, all the HNH bonds are exactly at the tetrahedral bond angle since there are only bond pairs in the structure and no lone pairs. Recall that lone pairs decrease the bond angke from the ideal value in a tetrahedron due to higher repulsion.
Acid chlorides can be prepared from carboxylic acids by treatment with ________.
A) PBr3
B) SOCl_2
C) KCl
D) both A and B
E) both B and C
Answer:D
Explanation:
Both thionyl chloride and phosphorus trichloride are used in the synthesis of acid chlorides from carboxylic acids. The thionyl chloride leads to a chlorosulphite intermediate before the acid chloride is formed
Modern commercial airliners are largely made of aluminum, a light and strong metal. But the fact that aluminum is cheap enough that airplanes can be made out of it is a bit of historical luck. Before the discovery of the Hall-Héroult process in , aluminum was as rare and expensive as gold. What would happen if airplanes had to be made of steel? The fuselage of the Airbus A380, which can carry passengers, is approximately a hollow aluminum cylinder without ends, long, wide, and thick (see sketch at right). The fuselage of an airplane Suppose this fuselage was made of steel (density ) instead of aluminum (density ), and let's say the average passenger has a mass of . We'll also assume the engines can't lift any greater mass than they already do. Calculate the number of passengers that the Airbus A380 could carry if its fuselage was made of steel.
To approach this problem, let's start by understanding what we have and what we need to find. We know:
1. The fuselage is in the shape of a cylindrical shell with approximate dimensions: length of 20 meters, diameter of 4 meters, and thickness of 0.01 meters.
2. The densities of aluminum and steel are 2700 kg/m³ and 7800 kg/m³ respectively.
3. The average mass of a passenger is 70 kg.
Now, we must find: the number of passengers that a steel-made Airbus A380 could carry, given that the total mass that the engines can lift stays the same.
First, we have to calculate the volume of the aluminum fuselage. Since the fuselage is a cylindrical shell, the volume can found using the formula for the volume of a cylinder: `π*r²*h` where r is the radius and h is the height or length of the cylinder in this context. The radius is the width divided by 2. To account for thickness, we subtract the volume of the inner cylinder from the volume of the outer cylinder.
To find the mass of the aluminum fuselage, we multiply the volume just calculated with the given density of aluminum.
Next, we calculate the mass of the equivalent steel fuselage. Given that the volume remains the same, we can multiply the volume of the fuselage with the density of steel to find the mass, as mass is the product of volume and density.
To find the difference in mass between the steel and aluminum fuselages, we subtract the mass of the aluminum fuselage from the steel fuselage.
This gives us 12785.653 kg, which is the additional weight when we switch from an aluminum fuselage to a steel fuselage.
Finally, we calculate how many passengers could be carried with this additional weight. Given the average mass of a passenger, knowing that this mass difference will directly affect how many passengers can be carried, we divide the weight difference by the average passenger mass of 70 kg to get the number of lost seats.
The mass of the aluminum fuselage is approximate 6768.88 kg, the mass of the steel fuselage is approximate 19554.53 kg. The difference in mass is about 12785.65 kg. This extra weight when changing to a steel fuselage would reduce the number of passengers by around 183.
So the aircraft would lose around 183 seats if the fuselage was made from steel instead of aluminum.
Learn more about Aluminum vs Steel Aircraft here:
https://brainly.com/question/32224504
#SPJ12
Final answer:
If the Airbus A380's fuselage were made from steel instead of aluminium, it would significantly increase the aircraft's weight, thereby reducing the maximum number of passengers it could carry, given the fixed capacity of the engines.
Explanation:
The question revolves around the impact of using steel instead of aluminium to construct the fuselage of an Airbus A380 and how that would affect the number of passengers it could carry. To address this, one must understand the properties that make aluminum preferable for such applications. Aluminum is a lightweight metal with a density significantly lower than that of steel. This attribute allows airplanes to carry more passengers and cargo without exceeding the maximum lift capacity of the aircraft's engines.
Steel, on the other hand, is much denser than aluminum. If the Airbus A380's fuselage were made from steel, its overall mass would substantially increase, thus reducing the number of passengers it could carry. As the engines are designed with specific thrust capacities that cannot be exceeded, the added weight from using steel would necessitate a reduction in the payload (e.g., passengers). Since the student hasn't provided the exact densities or other needed numerical values, a numeric calculation cannot be performed. However, the general principle is clear: using steel would mean transporting fewer passengers due to the increased weight of the aircraft's structure.
The evolution of aircraft construction materials from wood and fabric to metal alloys and composites has been instrumental in the advancement of modern aviation, leading to more efficient and larger aircraft, as exemplified by the Airbus A380, the world's largest commercial jetliner capable of carrying up to 850 passengers.
Lithium diisopropylamide is a strong, nonnucleophilic base. It is often freshly prepared by treating a certain reactant with n-butyllithium (n-BuLi). Draw the starting material and draw the product (lithium diisopropylamide). Include any charges, but you do not need to draw electron pairs.
Answer:
Starting material is Diisopropylamine.
Explanation:
By reacting Diisopropylamine with n-Butyllithium in dry cold conditions with Tetrahydrofuran as solvent, Lithium diisopropylamide is prepared. Please see the attached image for reference.
If 25 grams of NaI is mixed with excess amount Pb(NO3)2, what would be the product?
Answer:
If 25 grams of NaI is mixed with an excess amount of Pb(NO3)2 we get 38.45 grams of PbI2 and 14.18 grams of NaNO3
Explanation:
Step 1: Data given
Mass of NaI = 25.00 grams
Pb(NO3)2 is in excess
Step 2: The balanced equation
2NaI + Pb(NO3)2 → PbI2 + 2NaNO3
Step 3: Calculate moles of NaI
Moles NaI = mass NaI/ molar mass NaI
Moles NaI = 25.00/ 149.89 g/mol
Moles NaI = 0.1668 moles
Step 4: Calculate moles of PbI2 and NaNO3
For 2 moles of NaI we need 1 mol of Pb(NO3)2 to produce 1 mol of PbI2 and 2 moles of NaNO3
For 0.1668 moles of of NaI we will have 0.1668/2 = 0.0834 moles of PbI2 and 0.1668 moles of NaNO3
Step 5: Calculate mass of the products
Mass PbI2 = 0.0834 *461.01 g/mol
Mass PbI2 = 38.45 grams
Mass NaNO3 = 0.1668 mol * 84.99 g/mol
Mass NaNO3 = 14.18 grams
If 25 grams of NaI is mixed with an excess amount of Pb(NO3)2 we get 38.45 grams of PbI2 and 14.18 grams of NaNO3
the equilibrium constant for the reaction H2 (g) + I2 (g) <==> 2 HI (g)
Kp is 54.4. What percent of I2 (g) will be converted to HI (g) is 0.200 moled each of H2 (g) and I2 (g) are mixed and allowed to come to equlibrium in a 1.00 liter container?
The percentage of I2 converted = 78.6 %
Explanation:
Write down the given values
Kp= 54.4
The percentage of I2 will be converted to HI is 0.200 moled each of H2 and I2.
It should come to an equilibrium in 1.00 lit container .
Change in I2 (iodine) and H2 (hydrogen) = x in each
Change in HI = 2x
total ni (nickel)
number of moles = 0.2 -x + 0.2 -x + 2x
=0.4 moles
Mole fractions :
I2 = 0.2-x / 0.4 H2
=0.2-x / 0.4 HI
= 2x /0.4
Kp = HI ^2 / H2* I2
= (2x) ^2 / (0.2-x) ^2 = 54.4
by taking square root:
2x / 0.2-x = 7.375
= x=0.157
percentage of I2 converted = 78.6 %
Label the Following Materials as Polar, Ionic or Nonpolar and Describe Whether They are Soluble or Insoluble in Water HCl O2 CaCl2 N2 C2H6 KNO3 BeCl2 BCl3
Final answer:
HCl is a polar molecule that readily dissolves in water, while O2 and N2 are nonpolar and insoluble. Ionic compounds like CaCl2 and KNO3 are highly soluble in water. BeCl2 is soluble in water, while BCl3 is insoluble.
Explanation:
When classifying materials as polar, ionic, or nonpolar, it's important to consider the types of chemical bonds present and the distribution of charge.
HCl is a polar molecule due to the unequal sharing of electrons between hydrogen and chlorine. It will readily dissolve in water, forming an acidic solution.
O2 is a nonpolar molecule because oxygen atoms share the electrons equally. It is insoluble in water due to the differences in polarity.
CaCl2 is an ionic compound, where calcium ions (positive) and chloride ions (negative) are attracted to each other due to the strong electrostatic forces. It is highly soluble in water.
N2 is a nonpolar molecule with equal sharing of electrons. It is insoluble in water.
C2H6 is a nonpolar molecule, and it is insoluble in water.
KNO3 is an ionic compound, made up of potassium ions and nitrate ions, and it is highly soluble in water.
BeCl2 is a polar molecule due to the unequal sharing of electrons. It is soluble in water, forming acidic solutions.
BCl3 is a nonpolar molecule, and it is insoluble in water.
The vapor pressure of Substance X is measured at several temperatures:temperature (C) vapor pressure (atm)34 0.23644 0.29254 0.355Use this information to calculate the enthalpy of vaporization of X. Round your answer to 2 significant digits. Be sure your answer contains a correct unit symbol. Clears your work. Undoes your last action. Provides information about entering answers.
Answer:
ΔHv = 17.04 KJ/mol
Explanation:
T(°C) T(K) Pv(atm) 1/T(K) LnPv
34 307 0.236 0.00325733 - 1.4439
44 317 0.292 0.0031545 - 1.2310
54 327 0.355 0.003058 - 1.0356
Clausius-Clapeyron:
δLnP/δT = ΔH/RT²⇒ δLnP = ΔH/R (δT/T²)
∴ δT/T² = δ/δT(- 1/T )
⇒ δLnP/δT = - ΔH/R
Graphing: LnP vs 1/T
we get an ecuation that corresponds to a straight line:
y = - 2049.6x + 5.2331 ...... R² = 1
where the slope of this line is:
y = mx + b
⇒ m = - 2049.6 = - ΔH/R.....Clausius-Clapeyron
⇒ ΔH = (2049.6)(R)
∴ R = 8.314 E-3 KJ/mol.K
⇒ ΔHv = 17.04 KJ/mol
If you lived in Alaska, which of the following natural gases could you keep in an outdoor storage tank in winter: a. Methane (CH4) b. Propane (C3H8) c. Butane (C4HIO)? Explain why.
Answer:
Methane
Explanation:
The gas that you could keep in an outdoor storage tank in winter in Alaska is Methane.
The reason is the extreme low temperature during the winter. The boiling point of butane is 44 ºF ( -1ºC) and that of propane is a higher -43.6 º F but still within the range of average minimum winter temperature in Alaska (-50 ªF). Therefore we will have condensation in the tanks and not enough gas pressure.
Methane having a boling point of -259 ºF will not condense at the low wintertime temperatures in Alaska.
Nitrogen (N2) enters a well-insulated diffuser operating at steady state at 0.656 bar, 300 K with a velocity of 282 m/s. The inlet area is 4.8 x 10-3 m2. At the diffuser exit, the pressure is 0.9 bar and the velocity is 140 m/s. The nitrogen behaves as an ideal gas with k = 1.4. (a) Determine the exit temperature, in K, and the exit area, in m2. (b) For a control volume enclosing the diffuser, determine the rate of entropy production, in kW/K.
The problem is solved by applying the principles of thermodynamics and fluid dynamics for an ideal gas under isentropic conditions in a diffuser, and involving calculations for temperature, exit area and entropy production.
Explanation:This problem involves the principles of thermodynamics and fluid dynamics, specifically in relation to the behavior of nitrogen gas in a diffuser. To solve it, we need to apply the ideal gas law and the principles of energy and entropy conservation.
For part (a), we can start by using the formula for isentropic relations in an ideal gas, which states that T2/T1 = (P2/P1)^((k-1)/k), where k is the specific heat ratio of the gas. By substituting the given values, and also considering the conservation of mass (continuity equation), we can calculate the exit temperature (T2) and the exit area.
Similarly, for part (b), using the formula for rate of entropy production (ΔS_gen = m_dot*[s2 - s1 + R*ln(P2/P1)]), where m_dot is the mass flow rate and R is the specific gas constant, we can find the rate of entropy production.
Learn more about Gas Dynamics here:https://brainly.com/question/30649157
#SPJ2
On top of one of the peaks in rocky mountain national park the pressure of the atmosphere is 550 torr determine the boiling point of water at this location.
Answer:
The boiling point of water at 550 torr will be 91 °C or 364 Kelvin
Explanation:
Step 1: Data given
Pressure = 550 torr
The heat of vaporization of water is 40.7 kJ/mol.
Step 2: Calculate boiling point
⇒ We'll use the Clausius-Clapeyron equation
ln(P2/P1) = (ΔHvap/R)*(1/T1-1/T2)
ln(P2/P1) = (40.7*10^3 / 8.314)*(1/T1 - 1/T2)
⇒ with P1 = 760 torr = 1 atm
⇒ with P2 = 550 torr
⇒ with T1 = the boiling point of water at 760 torr = 373.15 Kelvin
⇒ with T2 = the boiling point of water at 550 torr = TO BE DETERMINED
ln(550/760) = 4895.4*(1/373.15 - 1/T2)
-0.3234 = 13.119 - 4895.4/T2
-13.4424= -4895.4/T2
T2 = 364.2 Kelvin = 91 °C
The boiling point of water at 550 torr will be 91 °C or 364 Kelvin
The boiling point of water decreases with altitude due to reduced atmospheric pressure. At an atmospheric pressure of 550 torr, which one might find on a peak in the Rocky Mountain National Park, the boiling point of water would be slightly higher than 90°C, but less than 100°C.
Explanation:The boiling point of water is impacted by the atmospheric pressure. At higher altitudes, like on a peak in Rocky Mountain National Park where the pressure is 550 torr, the atmospheric pressure is lower and results in a lower boiling point compared to sea level. This can be confirmed with the use of a vapor pressure curve.
Deciphering the vapor pressure curve: Usually, 500 torr corresponds to a temperature around 80-90°C. So, it can be inferred that the boiling point of water at 550 torr would be slightly higher than 90°C, but still less than 100°C, which is the boiling point of water at sea level at standard atmospheric pressure.
Summarizing the concept, the boiling point of a liquid increases as pressure increases and decreases as pressure decreases. In other words, the boiling point of water decreases with altitude as the atmospheric pressure decreases.
Learn more about Boiling Point here:https://brainly.com/question/2153588
#SPJ12
i. What is the Lewis structure for CH3CHCHOH? (If resonance is present, draw only one structure.)ii. What is the total number of valence electrons? ___________iii.What is the formal charge on each atom (excluding H atoms)? C_______ C_______ C_______ O_______iv. What is the ideal bond angle for the C-O-H atoms? _______________v. What is the hybrdization for the C atoms? C__________ C__________ C__________vi. Are there any resonance structures, Yes or No? _________
Answer:
i: answer is in attachment.
ii: 24 valance electron in overall structure
iii: carbon having positive charge while oxygen having negative
iv: a bond angle of approximately 104.5 degrees.
v: CH3 having sp3 hybridization and both CH having sp2 hybridization
vi: yes. resonance occur between CH=CH and oxygen.
Explanation:
iii: oxygen is electronegative so attraction of electrons occur at oxygen results in negative charge.
iv: a bond angle is about 104.5 degrees because the oxygen has 2 lone pairs and 2 bond pairs of electrons so lone pairs repulsion occur more than bonding pairs that's why the angle is less than that of an atom with tetrahedral or pyramidal geometry.
The Lewis structure for CH3CHCHOH comprises a chain of three carbon atoms with associated hydrogens and an alcohol group, having 22 valence electrons in total. The formal charges for the carbon and oxygen atoms are zero, the ideal C-O-H bond angle is approximately 109.5 degrees, the first and third carbon atoms are sp3 hybridized, and the second carbon is sp2 hybridized. There are no resonance structures for CH3CHCHOH.
Explanation:The Lewis structure for CH3CHCHOH can be drawn by considering that carbon typically forms four bonds, hydrogen forms one bond, and oxygen forms two bonds. Here's a step-by-step process: Place the carbons in a row since they are connected to each other, attach the three hydrogens to the first carbon, add a double bond between the second and third carbon, and complete the octets for each carbon. Attach the hydroxyl group (-OH) to the third carbon. After drawing this, complete the structure by adding lone pairs to the oxygen atom.
Total number of valence electrons: Carbon has 4 valence electrons, Hydrogen has 1, and Oxygen has 6. The compound has three carbons (3x4=12), four hydrogens (4x1=4), and one oxygen (1x6=6), totaling 22 valence electrons.
Formal charges on each atom are calculated by using the formula: Valence electrons - (Nonbonding electrons + 1/2 Bonding electrons). After calculating, you will find that the formal charges for the carbons and the oxygen in CH3CHCHOH are all zero.
The ideal bond angle for the C-O-H atoms in an alcohol group is approximately 109.5 degrees, based on a tetrahedral arrangement.
The hybridization for the carbon atoms depends on the number of sigma bonds and lone pairs around each carbon. For CH3CHCHOH, we have: first carbon (C1) is sp3 hybridized, second carbon (C2) is sp2 hybridized, and the third carbon (C3, which is part of the alcohol group) is sp3 hybridized.
Regarding the presence of resonance structures, there are no resonance structures for CH3CHCHOH since there are no delocalizable pi electrons or lone pairs adjacent to the pi bonds that could result in resonance.
Which of the following reagents convert(s) benzoyl chloride to phenyl propyl ketone?a. CH3CH2CH2MgBrb. CH3CH2CH2Lic. (CH3CH2CH2)2CuLid. Both a and b
Answer:C
(CH3CH2CH2)2CuLi
Explanation:
The reaction between acyl halides and Grignard reagents or acyl halides and organolithium compounds does not form ketones because the reagents ( Grignard reagent and organo lithium compounds) are too reactive hence the ketone intermediate reacts further to form tertiary alcohols hence the ketone cannot be isolated.
When a nitrile is treated with a base what is the organic compound?
A. ester
B. aldehyde
C. ketone
D. carboxylate ion
Answer:
D. Carboxylate ion
Explanation:
The nitriles are hydrolyzed wiyh aqueous soda, under heating, to form carboxilates and ammonia:
H3C-C≡CN + NaOH(aq) → H3C-C=OONa+ + NH3
Which of the following conditions remain constant in Charles's law?
Volume and pressure
Density and temperature
Pressure and number of moles
Temperature and number of moles
Answer:
Pressure and number of moles.
Explanation:
According to Charles law,
For an ideal gas, volume is directly proportional to temperature at constant pressure for a fixed amount of gas.
V ∝ T
[tex]\frac{V}{T}=constant[/tex]
From the law we can say that the two conditions are:
Pressure remains constant.Number of moles do not change (As the amount of gas is fixed).The condition that remains constant in Charles's law is Pressure and number of moles.
What is Charles's law?Charles's law states that the volume occupied by a fixed amount of gas is directly proportional to its absolute temperature, if the pressure remains constant.
The volume of a gas is directly proportional to it's number of moles.
Therefore, the condition that remains constant in Charles's law is Pressure and number of moles.
Learn more about Charles's law here:
https://brainly.com/question/16927784
#SPJ5
Chlorination of alkanes can produce a multitude of products. Determine the number of monochlorinated and dichlorinated products that can be obtained by chlorination of 3-methylpentane. (Consider constitutional isomers only. Do not count stereoisomers.)
Answer:
monochlorinated products: 4
dichlorinated products: 12
Explanation:
Chlorination of alkanes is a reaction that takes place when the chlorine is in presence of light. This actually decomposes the chlorine, and one atom of Chlorine substracts an hydrogen from the alkane. Now, this hydrogen substracted comes usually from the most substitued carbon, because it's more stable (A tertiary carbon is more stable than a secondary carbon, and this more stable than primary).
When this happens, the other chlorine atom, goes as electrophyle in that carbon and formed the chlorinated product. Now, although a tertiary carbon is more stable, we can still have (in minor quantities) chlorinated products that comes from a secondary and primary carbon. The first picture shows the general mechanism of the chlorination, and the possible products for a monochlorinated.
The second picture shows the possible dichlorinated products, which are in higher quantities than the monochlorinated basicallu because of the variety of positions the chlorine can be. So, second picture shows all the products.
The chlorination of 3-methylpentane can produce varying products, depending on the number of hydrogen atoms being substituted by chlorine. Monochlorination can produce 4 unique products, while dichlorination can yield 9 unique products.
Explanation:The chlorination process can result in multiple products due to the number of hydrogen atoms in 3-methylpentane that can be substituted by chlorine. The original compound, 3-methylpentane, has 12 hydrogen atoms. Therefore, monochlorination can produce various constitutional isomers. The unique monochlorinated constitutional isomers that can be obtained when we replace one hydrogen by one chlorine atom are 1-chloro-3-methylpentane, 2-chloro-3-methylpentane, and a pair of 3-chloro-3-methylpentanes, giving a total of four.
For dichlorination (two chlorine substituents), we consider each of the monochlorinated products and determine where the second chlorine atom can be placed. This will give 1,1-dichloro-3-methylpentane, 1,2-dichloro-3-methylpentane and others, totaling up to 9 unique dichlorinated constitutional isomers. Therefore,monochlorination of 3-methylpentane can produce 4 products and dichlorination can produce 9 products.
Learn more about Chlorination here:
https://brainly.com/question/31560014
#SPJ3
When baking soda (sodium bicarbonate or sodium hydrogen carbonate, NaHCO3) is heated, it releases carbon dioxide gas, which is responsible for the rising of cookies, doughnuts, and bread.
a) Write a balanced equation for the decomposition of the compound (one of the products is Na2CO3).
b) Calculate the mass of NaHCO3 required to produce 20.5 g of CO2.
Answer:
a. NaHCO₃ + HCl → NaCl + H₂O + CO₂
b. 39.14 g is the mass of NaHCO₃ required to produce 20.5 moles of CO₂
Explanation:
A possible reaction for NaHCO₃ to make dioxide is this one, when it reacts with hydrochloric to produce the mentioned gas.
NaHCO₃ + HCl → NaCl + H₂O + CO₂
Ratio in this reaction is 1:1
So 1 mol of baking soda, produce 1 mol of CO₂
Let's calculate the moles
20.5 g CO₂ / 44 g/m = 0.466 moles
This moles of gas came from the same moles of salt.
Molar mass baking soda = 84 g/m
Molar mass . moles = mass
84 g/m . 0.466 moles = 39.14 g
Consider the following reaction:
CuS(s) + O2(g) ⇌ Cu(s) + SO2(g)
A reaction mixture initially contains 2.9 M O2.
Determine the equilibrium concentration of O2 if Kc for the reaction at this temperature is 1.5.
To determine the equilibrium concentration of O2 in the given reaction, we need to use the equilibrium constant expression and the initial concentration of O2. The equilibrium constant (Kc) for the reaction is 1.5. By substituting the known values into the equilibrium constant expression, we can solve for the equilibrium concentration of O2.
Explanation:In order to determine the equilibrium concentration of O2 in the given reaction, we need to use the equilibrium constant expression and the initial concentration of O2. The equilibrium constant (Kc) for the reaction is 1.5. The reaction is in the form of a reversible reaction, so the concentrations of the reactants and products play a role in determining the equilibrium concentration of O2.
Using the equilibrium constant expression, we have:
Write the expression for Kc using the given reaction equation: Kc = [Cu][SO2] / [CuS][O2]Substitute the known values into the expression: 1.5 = [Cu][SO2] / (x)(2.9)Solve for x to find the equilibrium concentration of O2: x = ([Cu][SO2]) / (1.5 * 2.9)Plug in the values of [Cu] and [SO2] from the given reaction equation to calculate the equilibrium concentration of O2.
Learn more about equilibrium concentration of O2 here:https://brainly.com/question/36310916
#SPJ12
For the given reaction, the equilibrium constant Kc is the ratio of the concentrations of the products to the reactants. Without a change or shift in the equilibrium, the equilibrium concentration of O2 remains the same as its initial concentration, 2.9 M.
Explanation:This problem involves understanding the concept of equilibrium in chemical reactions. From the reaction,
CuS(s) + O2(g) ⇌ Cu(s) + SO2(g)
We know that at equilibrium, the rate of the forward reaction equals to the rate of the reverse reaction. Considering the equilibrium constant, Kc = [Products]/[Reactants], being given as 1.5, we also know that [Cu][SO2]/[CuS][O2] equals 1.5.
Since the concentration of a solid like CuS or Cu in the reaction does not affect the equilibrium, the equilibrium expression is simply [SO2]/[O2] = Kc
In the context of this question, we are provided that the initial concentration of O2 is 2.9 M and are asked to determine the equilibrium concentration of O2. Since there's no shift mentioned in the equilibrium, it indicates that no reaction has taken place. This means the equilibrium concentration of O2 remains the same as its initial concentration, that is, 2.9 M.
Learn more about Chemical Equilibrium here:https://brainly.com/question/3920294
#SPJ2
At a particular temperature, K = 1.00×102 for the reaction: H2(g) + F2(g)= 2HF(g) In an experiment, at this temperature, 1.40 mol of H2 and 1.40 mol of F2 are introduced into a 1.14-L flask and allowed to react. At equilibrium, all species remain in the gas phase. What is the equilibrium concentration (in mol/L) of H2?
The equilibrium concentration of H2 in the given reaction is approximately 0.614 mol/L.
Explanation:Given that the equilibrium constant (K) is 1.00×10^2 for the reaction H2(g) + F2(g) ⇌ 2HF(g), we can use the stoichiometry of the reaction to determine the equilibrium concentration of H2. Since 1 mol of H2 reacts with 1 mol of F2 to form 2 mol of HF, the concentration of H2 at equilibrium will be half of its initial concentration. Therefore, the equilibrium concentration of H2 in the 1.14-L flask would be 1.40 mol divided by 2 and then divided by 1.14 L, which gives us approximately 0.614 mol/L.
Learn more about Equilibrium concentration of H2 here:https://brainly.com/question/32441643
#SPJ12
The equilibrium concentration of H₂ is calculated to be 0.205 M.
To find the equilibrium concentration of H₂, we first need to set up an ICE (Initial, Change, Equilibrium) table:
Initial concentrations:
Initial concentration of H₂ = 1.40 mol / 1.14 L = 1.23 M Initial concentration of F₂ = 1.40 mol / 1.14 L = 1.23 M Initial concentration of HF = 0 MChanges in concentration:
Change in H₂ = -xChange in F₂ = -xChange in HF = +2xEquilibrium concentrations:
Equilibrium concentration of H₂ = 1.23 - xEquilibrium concentration of F₂ = 1.23 - xEquilibrium concentration of HF = 2xAccording to the equilibrium constant expression (K):
[tex]K = [HF]^2/ [H_2][F_2][/tex]
Substitute the equilibrium concentrations into the expression:
[tex]1.00 \times 10^2 = (2x)^2 / (1.23 - x)(1.23 - x)[/tex]
This simplifies to:
[tex]100 = 4x^2 / (1.23 - x)^2[/tex]
Taking the square root of both sides:
10 = 2x / (1.23 - x)
Solve for x:
10(1.23 - x) = 2x
12.3 - 10x = 2x
12.3 = 12x
x = 1.025
The equilibrium concentration of H₂ is:
[H₂ ] = 1.23 - 1.025 = 0.205 M
Combustion of hydrocarbons such as propane ( C3H8 ) produces carbon dioxide, a "greenhouse gas." Greenhouse gases in the Earth's atmosphere can trap the Sun's heat, raising the average temperature of the Earth. For this reason there has been a great deal of international discussion about whether to regulate the production of carbon dioxide.
1. Write a balanced chemical equation, including physical state symbols, for the combustion of gaseous propane into gaseous carbon dioxide and gaseous water.
2. Suppose 0.150kg of propane are burned in air at a pressure of exactly 1atm and a temperature of 12.0°C . Calculate the volume of carbon dioxide gas that is produced. Round your answer to 3 significant digits. L
Answer:
239 L
Explanation:
1. Propane reacts with oxygen to produce carbon dioxide and water:
[tex]C_3H_8 (g) + O_2 (g)\rightarrow CO_2 (g) + H_2O (l)[/tex]
Firstly, 3 carbon atoms are required on the right:
[tex]C_3H_8 (g) + O_2 (g)\rightarrow 3 CO_2 (g) + H_2O (l)[/tex]
Secondly, 8 hydrogens in total (4 water molecules) are required on the right:
[tex]C_3H_8 (g) + O_2 (g)\rightarrow 3 CO_2 (g) + 4 H_2O (l)[/tex]
On the right, we have a total of 10 oxygen atoms, this implies we need 5 oxygen molecules on the left:
[tex]C_3H_8 (g) + 5 O_2 (g)\rightarrow 3 CO_2 (g) + 4 H_2O (l)[/tex]
2. Calculate moles of propane using the the ratio of mass to molar mass:
[tex]n_1 = \frac{m_1}{M_1} = \frac{150 g}{44.1 g/mol} = 3.40 mol[/tex]
According to the stoichiometry, we have 3 times greater amount of carbon dioxide:
[tex]n_2 = 3n_2 = 3\cdot 3.40 mol = 10.2 mol[/tex]
Use the ideal gas law to solve for volume:
[tex]pV = nRT\therefore V = \frac{nRT}{p} = \frac{10.2 mol\cdot 0.08206 \frac{L atm}{mol K}\cdot 285.15 K}{1 atm} = 239 L[/tex]
What compound is produced when cyclohexene is treated with concentrated KMnO4?
A) hexanoic acid
B) adipic acid
C) cyclohexanecarboxylic acid
D) benzoic acid
E) succinic acid
Final answer:
The reaction of cyclohexene with concentrated KMnO₄ cleads to the formation of adipic acid due to oxidative cleavage of the carbon-carbon double bond.
Explanation:
When cyclohexene is treated with concentrated KMnO₄ (potassium permanganate), the reaction is an oxidative cleavage, and it produces a compound called adipic acid. This is because KMnO₄ is a strong oxidizing agent, which will typically cleave the double bond in the cyclohexene and oxidize the resulting fragments into carboxylic acids. Given that cyclohexene has a six-carbon ring, the oxidative cleavage will produce a six-carbon diacid, which is known as adipic acid.
Therefore, the correct answer to what compound is produced when cyclohexene is treated with concentrated KMnO₄ is B) adipic acid.
Mr. Auric Goldfinger, criminal mastermind, intends to smuggle several tons of gold across international borders by disguising it as lumps of iron ore. He commands his engineer minions to form the gold into little spheres with a diameter of exactly and paint them black. However, his chief engineer points out that customs officials will surely notice the unusual weight of the "iron ore" if the balls are made of solid gold (density=19.3g/cm^3 ). She suggests forming the gold into hollow balls instead (see sketch at right), so that the fake "iron ore" has the same density as real iron ore (5.15g/cm^3). One of the balls of fake "iron ore," sliced in half. Calculate the required thickness of the walls of each hollow lump of "iron ore." Be sure your answer has a unit symbol, if necessary, and round it to significant digits.
The volume of the hollow gold sphere can be calculated by subtracting the volume of the inner void (hollow space) from the volume of the entire sphere.
What is the thicknessTo get the same density as real iron ore (5.15 g/cm³), the hollow gold spheres must be designed in a way that the total volume of gold is equal to the volume of the iron ore the same mass. The density formula can be rearranged to solve for volume:
Density = Mass / Volume
Volume = Mass / Density
Density of fake "iron ore" = Mass of fake "iron ore" / Volume of fake "iron ore"
The equation:
Density of fake "iron ore" = Mass of fake "iron ore" / Volume of fake "iron ore"Volume of hollow sphere = (4/3) * π * [(radius of outer sphere)³ - (radius of inner sphere)³]
5.15 g/cm³ = Mass of fake "iron ore" / [(4/3) * π * (1³ - (1 - t)³)]
So one then Solve for t:
t = 1 - ( (3 * Mass of fake "iron ore") / (4 * π * 5.15) )^(1/3)
Read more about thickness here:
https://brainly.com/question/24268651
#SPJ1
To achieve the same density as real iron ore, the required thickness of the walls of each hollow lump of 'iron ore' should be approximately 4.02 cm.
To calculate the required thickness of the walls of each hollow lump of 'iron ore,' we can use the formula for density: density = mass/volume.
Since the density of real iron ore is 5.15 g/cm^3 and we want the fake 'iron ore' to have the same density, we can set up the following equation:
5.15 g/cm^3 = (mass of gold)/(volume of hollow sphere)
We know that the mass of gold is the same as the volume of the hollow sphere, since the density of gold is 19.3 g/cm^3. Therefore, we can rewrite the equation as:
5.15 g/cm^3 = 19.3 g/cm^3 / (4/3 * π * (outer radius^3 - inner radius^3))
Solving for the outer radius, we get:
outer radius = (3 * (19.3 g/cm^3) / (5.15 g/cm^3 * 4 * π) )^(1/3) ≈ 4.02 cm
And since the inner radius is 0 (since it's hollow), the required thickness of the walls is the difference between the outer radius and the inner radius:
required thickness = outer radius - inner radius = 4.02 cm - 0 cm = 4.02 cm
For more such questions on thickness, click on:
https://brainly.com/question/30299844
#SPJ11
Calculate the ATP yield for the complete oxidation of the 16-carbon unsaturated fatty acid palmitoleic acid (a 16:1-Δ9 fatty acid). (You should consider the β-oxidation steps, processing of acetyl-CoA through the citric acid cycle, and electron transport. Production of one GTP should be considered the equivalent of production of one ATP. Enter your answer to three significant figures.) ATPs are gained for each palmitoleic acid oxidized
Answer: Total ATP yield for the complete oxidation of the 16-carbon unsaturated fatty acid palmitoleic acid (a 16:1-Δ9 fatty acid) = 108 ATP molecules.
Note: Two ATP molecules are used in the activation of palmitoleic acid to palmitoleoyl-CoA. Therefore the net ATP yield is 106 molecules.
Explanation:
Palmitoleic acid is a 16-carbon fatty acid. The complete oxidation of palmioleic acid yields eight acetyl-CoA molecules and 7FADH2 and &NADH2. The overall equation for the reaction is shown below
Palmiltoleoyl-CoA + 7CoA + 7 FAD + 7NAD+ + 7H2O---> 8 acetyl-CoA + 7FADH2 + 7NADH + 7H+
Each of the eight acetyl-Coa molecules enters the citric acid cycle to yield three NADH and one FADH2 which equals to; 8 * 3NADH = 24NADH and 8 * 1FADH2 = 8FADH2. Also the substrate level phosphoryation by succinyl-CoA synthetase yields 8 GTP molecules which later is converted to 8 ATP molecules.
Total FADH2 = 7 + 8 = 15FADH2
Total NADH = 7 + 24 NADH = 31 NADH
Each FADH2 and NADH enters the electron transport chain to produce 1.5 ATP and 2.5 ATP per molecule respectively.
1.5 * 15 FADH2 = 22.5 ATP molecules
2.5 * 31 NADH = 77.5 ATP molecules
Total ATP yield for the complete oxidation of the 16-carbon unsaturated fatty acid palmitoleic acid (a 16:1-Δ9 fatty acid) = 8 +22.5+77.5 = 108 ATP molecules.
Note: Two ATP molecules are used in the activation of palmitoleic acid to palmitoleoyl-CoA. Therefore the net ATP yield is 106 molecules.
The complete oxidation of palmitoleic acid yields 129 ATPs through several steps, including activation, the production of acetyl-CoA, the citric acid cycle, and reoxidation of reducing equivalents.
Explanation:The complete oxidation of palmitoleic acid yields 129 ATPs. This is determined by several steps. First, 1 mole of ATP is used for activation. Then, 8 moles of acetyl-CoA are produced, each yielding 10 moles of ATP in the citric acid cycle, resulting in 80 ATPs. The β-oxidation reactions are repeated seven times, producing 7 moles of NADH and 7 moles of FADH2. These reducing equivalents are reoxidized through respiration, yielding 2.5-3 moles of ATP per NADH and 1.5-2 moles of ATP per FADH2. Overall, this results in approximately 49 moles of ATP from NADH and 14 moles of ATP from FADH2. Therefore, the total ATP yield for the complete oxidation of palmitoleic acid is 129 ATPs.
The standard enthalpy of certain reaction is approximately constant at +125kJmol-1 from 800K to 1500K. The standard Gibbs energy is +25kJmol-1 at 1150K. Estimate the temperature at witch the equilibrium constant becomes greater than 1.
Answer:
T = 3006.976 K
Explanation:
∴ ΔH° = 125 KJ/mol ( 800K - 1500K)
∴ ΔG° = 25 KJ/mol (1150 K)
⇒ T = ? ∴ K > 1
In the equilibrium:
K = e∧(ΔG°/RT)∴ K > 1
If ΔG°/RT = 1
⇒ e∧(1) = 2.72 > 1
∴ ΔG°/RT = 1
⇒ T = ΔG°/R = (25 KJ/mol)/(8.314 E-3 KJ/mol.K)
⇒ T = 3006.976 K
verifying:
K = e∧(ΔG°/RT)⇒ K = e∧(25/((8.314 E-3)(3006.976)))
⇒ K = 1.000000061 > 1
Final answer:
The student is asking about estimating the temperature at which the equilibrium constant becomes greater than 1 based on the given standard enthalpy and Gibbs energy values.
Explanation:
The given question is related to standard enthalpy and Gibbs energy of a reaction, and the estimation of temperature at which the equilibrium constant becomes greater than 1.
Firstly, it is stated that the standard enthalpy of the reaction is approximately constant at +125 kJmol-1 from 800K to 1500K. This information helps us understand the change in enthalpy with respect to temperature.
Secondly, the standard Gibbs energy is given as +25 kJmol-1 at 1150K. This value allows us to calculate the equilibrium constant using the equation: ΔG = -RT lnK.
To estimate the temperature at which the equilibrium constant becomes greater than 1, we need to solve for temperature in the equation K = e-ΔG/T and find the value of T that results in K > 1.
Be sure to answer all parts. The sulfate ion can be represented with four S―O bonds or with two S―O and two S═O bonds. (a) Which representation is better from the standpoint of formal charges? four S―O bonds two S―O bonds and two S═O bonds (b) What shape is the sulfate ion, and what hybrid orbitals of S are postulated for the σ bonding? bent tetrahedral trigonal planar trigonal pyramidal spmdn where m = and n = (c) In view of the answer to part (b), what orbitals of S must be used for the π bonds? What orbitals of O? sulfur: 3d 3p 2p 3s oxygen: 3p 2p 2s 3s
Answer:
a) Representation - (in attachment)
b) Tetrahedral geometry and
c) [tex]sp^{3}[/tex] hybrid orbitals invovle sigma bonding.
[tex]\pi[/tex] orbitals are formed by the overlapping of d-orbitals of sulfur with p-orbitals of oxygen.
Explanation:
a)
Representation in attachment.
The overall charge in the both structures are -2. The structure (b) is favored by the resonance structures since the formal charge with in the species are remained.
Therefore, structure (b) is the better representation of sulfate ion.
b)
In sulfate ion, sulfur atom is attached with four different oxygen atoms. According to the VSEPR theory , the sufate ion has tetrahedral geometry.
There is four sigma bonds and zero lone pairs present on the central metal atom.
Hence, the hybridization of the sulfur atom is [tex]sp^{3}[/tex]
c)
The s and p orbitals of sulfur invovles hybridization and form sigma bonds.The orbitals of sulfur involves [tex]\pi[/tex] bonding.
Therefore, [tex]\pi[/tex] bonds are formed by the overlapping of d-orbitals of sulfur with p-orbitals of oxygen.
The sulfate ion is best represented with four S―O single bonds maintaining a tetrahedral geometry and sulfurs' sp³ hybridization. The pi bonds are formed due to the overlap of sulfur's 3d and oxygen's 2p orbitals.
Explanation:The sulfate ion can be represented better with four S―O single bonds. This equalizes the formal charges, since every oxygen atom carries a charge of -2 while sulfur carries a charge of +6.
The geometry shape of the sulfate (SO4²-) ion is tetrahedral, and the hybridization of the sulfur (S) atom is sp³, based on the fact that there are four regions of electron density around sulfur in the sulfate ion. These regions come from the four sigma bonds formed between sulfur and oxygen.
In view of the tetrahedral shape of the sulfate ion, the sulfur atom uses its 3p orbitals and 3s orbital to form sp³ hybrid orbitals for sigma bonds with the oxygen atom's 2p orbitals. The double bonds observed in some resonance structures of sulfate ion arise due to the overlap of the 3d orbitals of sulfur with the 2p orbitals of oxygen to form pi bonds.
Learn more about Sulfate Ion here:https://brainly.com/question/30201446
#SPJ3